Spectra-precision Layout Pro Field Software Quick Start Guide Bedienungsanleitung

Quick Start GuideLayout Pro Field Software

1Getting StartedDouble-tap the Layout Pro icon on the data collector ([1]) or total station ([2]) desktop.With a data collector, the main menu ([3]) w

2Working With JobsStarting a New Job 1. Tap Jobs on the main menu. This opens the Jobs menu.2. Tap Create New Job.3. Using the keypad, key in a name f

3Settings and PreferencesFrom the main menu, tap Settings. The Settings & Preferences window allows you to set:• The instrument used ([1]) (with a

4Entering a Plan from a BlueprintEntering aBasic Plan1. From the main menu, tap Plan.2. Tap Input Plan to begin entering your plan.The following table

5Adding an Arcto a Plan1. Select Enter an Arc from the Tools menu located at the bottom of the Enter Line window.2. Choose the start point (P1) and en

6– Flip button: Tapping this button provides the other possible orientation for the arc. Tapping again this button will bring the arc back to its init

7minus sign before the Y coordinate if the point must be located below the horizontal axis (see examples below).• Repeat the previous two steps until

8• Tap on the Finish button if you agree (below right), otherwise tap <Back to redo the placement or select another point pattern.The points from t

9Closure Check As you enter the last point from the blueprint, a dialog box appears and asks whether you want to add the point or connect it to an exi

SOFTWARE END USER LICENSE AGREEMENT (EULA)(TNL - TEBV)IMPORTANT, READ THIS AGREEMENT CAREFUL-LY. BY INSTALLING OR USING ALL OR ANY POR-TION OF THE SOF

103. Set the New lines intersect with existing lines option as follows:– Check it on if you want to create points for every intersection.– Clear it if

11Creating Pointsfrom an ImportedDXF FileIntroductionYou can create points from a DXF file you import into the open job. The points will be part of th

12Icon FunctionTap on this button to select an arc on the map. Layout Pro then sug-gests you create a point at the center point of the selected arc.Ta

13• Tap to define the elevation of your point(s); (see table above).If you selected a line through , two additional buttons can be seen on the scre

14Making Computations from your Entered Plan1. Tap Plan on the main menu.2. Tap Compute with Plan on the submenu.3. Tap in the lower-right corner of

156. Select Compute Angle to compute the angle between any three points:7. Select Compute Down & Out to compute a point’s down and out distance fr

16Setting Up a Connected Total StationBefore using a total station to perform a stakeout or survey, you must set up your total station (in the locatio

175. Select Built-in Radio and then enter the radio channel (Radio Channel) and network ID (Network ID) required to communicate with the FOCUS 30.The

187. Tap ok to return to the Setting & Preferences screen. From this screen, you can now use the Instrument Settings button to access other instru

19Station SetupIf you choose to set up the total station over a marked point from the plan (Marked Points choice, diagram [1] below), you will need to

2.4. License Restrictions.2.4.1 You shall not (and shall not allow any third par-ty to): (a) decompile, disassemble or otherwise re-verse engineer the

20• Tap Next.• Select the point from the plan where to set up the instrument ([1]). Set up the instrument at this location.• Tell Layout Pro whether y

214. If you choose Reference Line, tap Next. Two options are possible:• Either you set up the instrument on the origin of the reference line. (The ori

22Setting the Elevation of the Instrument Location (with instrument located either on or off the line): When selecting the Reference Line method in th

235. If you choose Any Location (see also diagram below):• Tap Next.• Tell Layout Pro whether you want to measure elevation (Yes/No). If you want to d

24Performing StakeoutNote: Unless otherwise specified, all the instructions given in this section apply to both mechanical and robotic stations. Whene

25The instrument is always shown at the top of the screen and the green line connecting the instrument to the rod location is always vertical. A blue

26With a robotic total station, you can use the Shoot button to take a measurement (the instrument will switch to whatever EDM mode is set in the inst

27Stakeout Using aReference Line1. When everything is set up correctly (see Station Setup on page 19), tap Line from the Layout menu.2. Select two poi

28Key in the down and out positions for the point you want to stake.Tap Next. Layout Pro then computes the coordinates of the stake point.With a mecha

29Stakeout Using aReference Arc1. When everything is set up correctly (see Station Setup on page 19), tap Arc from the Layout menu.2. Define the refer

are non-refundable once paid. You shall be responsi-ble for all taxes, withholdings, duties and levies aris-ing from the order (excluding taxes based

303. Tap Next. You can choose between Stake Out Points and Show Position (see screen below).• If you choose Stake Out Points and tap Next, a screen ap

31For both types of total stations, complete the procedure as you would for a stake point selected from the entered plan.• If you choose Show Position

32Measuring Features1. When everything is set up correctly (see Station Setup on page 19), tap Measure Features from the Layout menu. You may choose t

Quick Start GuideLayout Pro Field Software©2012-2014 Trimble Navigation Limited. All rights reserved. Spectra Precision is a Division of Trimble Navig

fessional Services and Trimble, not being a contract-ing party, has no liability related to such services.8. Limitation of Remedies and Damages.8.1. N

• 11.3.2. If You obtained this Software outside the U.S., this Agreement is governed by the laws of The Netherlands (country where Trimble Eu-rope B.V

Data Collector Warranty Program Spectra Precision would like to make you aware of the warranty program. A new data collector that has been purchased a

Table of ContentsGetting Started ..................1Working With Jobs.......