Spectra-precision Survey Pro v4.6 Recon-Nomad Reference Manual Bedienungsanleitung Seite 203
- Seite / 481
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Survey Menu – GPS Module
R-195
Rover Setup
The Rover Setup screen is used to set the RTK rover receiver, and to
configure or check the base reference position in Survey Pro.
Rover Status: displays the status of the rover setup in
Survey Pro.
Base set at: displays the current base point. This will be
empty if the base is not set.
Detail : opens a screen that displays the geodetic
position of the base.
Antenna: displays antenna setup for this receiver. It will
be in one of three states:
• Last Antenna for this receiver: is displayed when
you have not yet set the rover in Survey Pro. This
value is the previous antenna measurement you
used with this receiver.
• Selected Antenna: is displayed when you have
entered new antenna measurements using the Receiver
Antenna screen (Page R-191).
• Antenna Set: is displayed when you have already set the
rover in Survey Pro, and this receiver was used as the rover.
Measured: is where you enter the height of the antenna, measured to
the location specified on the Receiver Antenna
screen (Page R-191).
Offset: displays the vertical and/or slant offset values for the selected
antenna. Entering antenna offsets is explained on the Receiver
Antenna screen, (Page R-191).
Setup HR : opens the Receiver Antenna screen (Page R-191).
Post Processing Recording Interval: is where you set the period for
logging GPS raw data for post processing. Set it to Off to disable post
processing data collection.
Set Rover: sets the receiver as an RTK rover. If a Post Processing
Recording Interval is selected, a file will be opened and logging of raw
GPS measurements for post processing will start. This will be a stop
and go data file, and the site ID and antenna measurement will be
recorded in the file with each point occupation at the rover
- SURVEY PRO 1
- Table of Contents 3
- Welcome 9
- Main Menu 11
- Surveying Mode 12
- Map View 12
- Quick Pick 12
- Battery Level 12
- Other Command Bar Buttons 13
- File Menu 15
- Open / New 16
- New Job 17
- External Control File) 18
- Create a New Job 3 19
- Control File) 20
- Save As 23
- Import *.JOB Coordinates 25
- Import *.CR5 Coordinates 26
- Import *.GPS Coordinates 26
- Import *.TXT Coordinates 26
- Import LandXML Coordinates 28
- Confirm Point Replace 29
- Export – Screen Two 31
- Export *.JOB Coordinates 31
- Export Old *.JOB Coordinates 31
- Export *.CR5 Coordinates 32
- Export *.TXT Coordinates 32
- Export *.CSV Coordinates 33
- Export LandXML (.XML) File 33
- Import Control Points 34
- Backup / Restore Job 34
- Backup / Restore – Backup 37
- Backup/Restore – Restore 38
- Transfer 39
- Register Modules 40
- About Survey Pro 41
- Job Menu 43
- NOTICE: 47
- Level Method 48
- Units Settings 49
- Format Settings 50
- Files Settings 51
- Descriptions Settings 52
- Surveying Settings 53
- Scale Settings 54
- Calculate Scale 55
- Screen Two 56
- Screen Three 56
- FGCS Defaults 62
- Repetition Settings 63
- Date/Time Settings 64
- Buttons Settings 65
- Edit Points 68
- Edit Point – General 70
- Point Feature Attributes 71
- Edit Point – Location 71
- Edit Point – Geodetic 72
- Edit GPS Point Flags Screen 72
- Edit Polylines 73
- Screen Four – Add/Edit Curve 75
- Adding a Spiral 76
- Adding a Vertical Curve 76
- Edit Alignment 78
- Edit Segment – Spiral Card 83
- Auto Linework 85
- View Raw Data File 89
- Raw Data Note 90
- Code Edit 91
- View DTM 92
- Layers for Staking DTM 93
- Choose Polyline 94
- Add/Edit Break-lines 94
- Edit Polyline 95
- Points on DTM Layer 96
- 3D View 97
- 3D View Settings 98
- Manage Layers 99
- Job Information 100
- Calculator 101
- Manage Pictures 103
- Take Picture 104
- Job Menu – GPS 107
- Settings 108
- Receiver Setup 109
- Rx Settings 111
- Data Modem Settings 112
- Modem Serial Comms Screen 114
- Radio Settings Screen 114
- Cell Phone Settings Screen 116
- General Settings 117
- Measure Mode Settings 120
- Post Process Settings 122
- Job Menu – Basic GPS 123
- Change Settings 125
- Bluetooth Setup Wizard 126
- Radio Settings 127
- Change Radio Settings Screen 128
- Date/Time 130
- Buttons 130
- General 130
- Survey Menu 131
- Backsight Setup 132
- Backsight Solved 133
- Check Backsight 135
- Check by Distance Results 136
- Check by Angle Results 136
- Backsight Circle 137
- Traverse / Sideshot 138
- Describe Point 139
- Results 139
- Traverse Now or Later? 140
- New Occupy Point 141
- Point Exists 142
- Remote Shot (Remote Mode) 143
- Repetition Shots 144
- Multiple Sideshots 146
- Radial Sideshots 147
- 1_ft back 148
- 3_ft right 148
- Horizontal Angle Offset 149
- Vertical Angle Offset 150
- Auto Collect 151
- Auto Collect – Screen Two 152
- Corner & 2 Lines 153
- Corner & Angle 154
- Corner & Offset 155
- Corner & Plane 156
- Surface Scan 157
- Angle Grid 158
- Surface Scan Statistics 159
- Surface Scan Results 159
- Video Scan 160
- Video Scan Settings 163
- Shoot From Two Ends 164
- Record Mode 165
- Resection 166
- Resection – Screen Two 167
- Save Point 167
- Remote Elevation 169
- Check Point 170
- Solar Observation 171
- The Enter Shot Data Screen 174
- Sun Shot Procedure Summary 174
- Remote Control 176
- Turn To 177
- Results Card 178
- Video Card 179
- Video Display Options 180
- Video Settings 181
- Map Card 182
- Aim Card 182
- Foresight Card 183
- GeoLock Settings 184
- Survey Menu – GPS 185
- GPS Status 186
- Cell Modem 188
- Post Process 188
- Sky View 189
- Sat Info 190
- Position 191
- Start GPS Survey 192
- Choose Projection Mode 193
- Choose Base Setup 194
- Connect To Receiver 195
- Select Geoid Model 195
- Base Setup 197
- Receiver Antenna 199
- Vertical Offset 200
- Base Setup Two – SET 201
- Base Setup Two – GET and SET 201
- Rover Setup 203
- Solve Localization 204
- Data Collection 205
- Feature Collection Screen 206
- Offset Shots 207
- Occupy Data Points Screen 209
- Control Points 210
- Check Control Point Screen 211
- Occupy Control Point Screen 212
- Post Processing 213
- End GPS Survey 217
- Projection 219
- Projection Details 221
- Localization Set Zone 221
- Select Coordinate System 222
- Horizontal Card 226
- Vertical Card 226
- Localization Calculator 227
- Solve Localization – Results 228
- Select Database 233
- Key in Zone 234
- Key In Zone - Ellipse 236
- Key In Zone - Results 238
- Ground Coordinates 239
- Ground Coordinates - Scale 240
- Ground Coordinates - Results 241
- Import GPS Control 243
- Review Results and Finish 245
- Single Point Results 246
- Multiple Point Results 247
- Receiver Information 248
- Adjust with Projection 249
- Coordinate System 251
- Projection Calculator 254
- File Management 257
- Recoverable Files 258
- Survey Menu – Basic 259
- Start Survey – More than One 262
- Matching Base Point 262
- GPS Backsight/Resection 263
- Occupy Control Setup 264
- Occupy Control Point 264
- Resection for New Base Point 264
- Traverse Base 268
- Leveling Menu 273
- Select/Create Loop 274
- New Level Loop – Screen Two 275
- Level Notes 275
- Level Notes Settings 276
- Leveling Shots 278
- Leveling Shot Results 278
- Leveling Side Shot 279
- Leveling Stakeout 280
- Turn to Benchmark 280
- 2 Peg Test 282
- 2 Peg Shots 283
- Peg Test Results 283
- Adjustment 284
- Adjustment – Preview Screen 285
- Leveling Remote Control 286
- Stakeout Menu 287
- Stake Points 288
- Stake Points – Screen Three 290
- ) dialog box 290
- Instrument Stakeout 291
- Remote Staking 292
- Stake List of Points Screen 293
- Edit Point List 294
- Stake to Line 295
- Stake to Line – Screen Two 296
- Remote Stake to Line 297
- Offset Staking 299
- Offset Staking – Screen Four 302
- specified) 302
- Offset Staking – Screen Five 303
- screen 304
- Offset Staking – Screen Six 304
- Slope Staking 306
- Slope Staking – Screen Three 307
- Slope Staking – Screen Four 308
- Slope Staking – Screen Five 310
- Slope Staking Offset Stake 311
- Point Slope Staking 313
- Stake Line and Offset 317
- value increases 318
- screen, described 318
- screen, which is 319
- Screen Summary 319
- Stake Curve and Offset 320
- Stake Spiral and Offset 324
- Summary 327
- Show Station 328
- Show Station – Screen Two 329
- Store Offset Points 330
- Stake DTM 333
- Choose a Centerline 335
- Stake DTM – Screen Two 336
- Station Staking 338
- Cross-Section View 339
- Define a Location 342
- Where is Next Point 344
- Stakeout Menu – GPS 347
- Line and Offset 355
- Curve and Offset 356
- Spiral and Offset 356
- Show Station and Offset 356
- Inverse Menu 361
- Inverse Point to Point 362
- Inverse Point to Line 363
- Inverse Point to Polyline 364
- Inverse Point to Multiple 366
- Inverse Point to Location / 367
- Cogo Menu 369
- Point in Direction 370
- Intersection 371
- Offset Line 373
- Offset Points 374
- Station Offset 375
- Corner Angle 376
- Compute Area 377
- Triangle Solutions 378
- Map Check 379
- Add / Edit Line 380
- Add / Edit Curve 380
- Add to Map 381
- Predetermined Area 382
- HD/VD to SD/ZA 384
- SD/ZA to HD/VD 385
- AU Conversion 386
- Average Points 387
- Average Points – Screen Two 388
- Curve Menu 389
- Curve Solution 390
- Results: 391
- Known PI and Tangents 392
- Three Point Curve 393
- Compute Radius Point 395
- Line Tangent to Circles 397
- Curve Layout 398
- : is the distance 399
- Chord Dist 400
- Traverse on Curve 402
- Parabolic Curve 404
- Parabolic Layout 406
- Straight Grade 408
- Spiral Layout 410
- Traverse on Spiral 411
- Roads Menu 413
- Add/Edit Templates 414
- Edit Template 415
- Edit Segment 416
- Edit Alignments 417
- Add/Edit Roads 417
- Roadname 418
- The Road Card 419
- Roads Report Screen 419
- Road Profiles Screen 421
- The Templates Card 422
- Add / Edit Template Screen 423
- The Widenings Card 424
- Add / Edit Widening Screen 425
- Super Elevations Card 426
- Road Stakeout 429
- Stake Road – Screen Three 431
- Stake Road – Screen Four 432
- Stake Road – Screen Five 434
- Road Slope Staking 435
- H. Map Card 436
- V. Map Card 436
- Slopes Card 437
- Cut/Fill Hinge Points Cards 437
- Road Station and Offset 438
- Alignment Card 439
- Cross-Section Card 440
- Shot Data Card 440
- Station Equation 441
- Adjust Menu 443
- Translate 445
- Traverse Adjust 447
- Traverse Adjust – Results 451
- Miscellaneous Screens 453
- Past Results 454
- Create Points 455
- Edit Description List 456
- Trimble Slant HR -> HR 457
- Convert Slant HI to HI 457
- Quick Pick Editor 458
- Select Point(s) 459
- Map Display Options 462
- Manage Basemaps 463
- Edit Basemaps 464
- Smart Targets 465
- Manage Smart Targets 466
- Edit Smart Target 467
- Appendix A 469
- Lambert Zones 470
- ...........181, R-392 473
- .................. 181 474
- ............... 181 474
- .............. R-51 474
- ......148, R-140 474
- ..........R-365, R-366 477
- ..................R-366 477
- ...........148, R-199 477
Verwandte Produkte und Handbücher für Software Spectra-precision Survey Pro v4.6 Recon-Nomad Reference Manual
Software Spectra-precision Survey Pro v4.5 Recon and Nomad Reference Manual Bedienungsanleitung
(469 Seiten)
(469 Seiten)
Software Spectra-precision Survey Pro v4.5 Recon and Nomad User Manual Bedienungsanleitung
(379 Seiten)
(379 Seiten)
Software Spectra-precision Survey Pro v3.80 Recon iPAQ Reference Manual Bedienungsanleitung
(261 Seiten)
(261 Seiten)
Software Spectra-precision Survey Pro CE v3.80 Ranger GPS Reference Manual Bedienungsanleitung
(93 Seiten)
(93 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern